Testing Equipment

Approx. Rs 65,000 / NumberGet Latest Price

Product Details:

The Pendulum Impact Tester is designed for conduction Izod & Charpy Test. The Pendulum is mounted on anti friction bearings. It has two starting positions, the upper one for Charpy and the lower one for Izod testing. On release, the Pendulum swing down to break the specimen and the energy absorbed in doing so is measured as the difference between the height of drop before rupture & height of raise after rapture of the test specimen and is read from the maximum pointer on the dial scale. Charpy Test: The Charpy test piece rests on alloy steel supports anvils fitted on the base of the machine rigidly held in position by alien screws. End stopper is provided for quickly & accurately locating the test piece centrally between the supports. Izod Test The Izod test piece is clamped vertically in Izod support anvils, fitted on the base of the machine. The support is provided with a machined vertical groove to suit the test piece size. The front clamp piece & alien screw enable clamping of the test piece in correct height with the help of Izod setting gauge supplied. Controls of Pendulum: The Pendulum supported in the starting positions is by a self resetting latch. The release mechanism is operated by lever. The Pendulum release latch is operated only when this lever is operated.
Specifications:

• Maximum Capacity - 300 J / 168 J
• Minimum Scale Graduation - 2 J
• Overall Size (Approx.) - 1.65 m (H), 1.1 m x 0.45 mx
• Net Weight (Approx.) - 375 Kg.

Approx. Rs 45,000 / NumberGet Latest Price

Product Details:

Hardness Testers Models SI RAS, SI RASM, SI RAB-1, SI RAB-250, SI TWIN are manually operated. All these models are suitable for testing hardness of metals & alloys of all kinds hard or soft, whether flat, round or irregular in shape. These testers are simple in design & easy to operate, yet sensitive & accurate. Various models from the wide range are suitable for Engg. Colleges, laboratories, toolroom, inspection departments, factories etc. These testers strictly conform to IS: 3804-1988, BS: 891 parts 1&2, ASTM:E18 for Rockwell Test, IS: 2281-1983, BS: 240, ASTM:E10 for rockwell Test & IS: 5073-1988, ASTM:E18 for Rockwell Superficial Test.

Salient FeaturesMODEL : SI RAS : Automatic load selection with automatic zero setting dial gauge. Manual Operation.MODEL : SI RASM : Similar to 'SI RAS1 but motorised model. Semiautomatic operation for production testing. Drive motor single phase 230V 50 cycles.ROCKWELL COMBINED SYSTEM MODEL SI RAB-1 : Automatic load selection with automatic zero setting dial gauge. Facility for rockwell Tests with 187.5 kgf. load with 2.5 mm ball indentor, additional load 250 kgf. with 5 mm ball Indentor for testing hardness of non- ferrous metals. Manual Operation.MODEL : SI RAB-250 : Similar to 'SI RAB-11 but bigger capacity Diamond Holder is guided in a set of two bail cage, which enables testing of small pins having dia. less than 6 mm (upto 3mm dia)ROCKWELL SUPERFICIAL COMBINED SYSTEM MODEL : SI TWIN : Manual load selection with automatic zero setting dial gauge. Manual Operation. Diamond Holder is guided in a set of two ball cage, which enables testing of small pins having dia. less than 6 mm. (upto 3 mm dia.)

Approx. Rs 70,000 / NumberGet Latest Price

Product Details:

Used for testing crushed rock, crushed slag, crushed and uncrushed gravel for resistance to abrasion. 

Specification:The machine consists of a hollow cylinder mounted horizontally on a sturdy frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrassive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-33 r.p.m. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with abrasive charges consisting of a set of twelve hardened steel balls, approximately 48mm dia. Suitable for operation on 440 volts, 3 phase, 50 cycles, A.C. supply

Approx. Rs 12,000 / PieceGet Latest Price

Product Details:

aggregate impact testing machine           

Approx. Rs 68,000 / NumberGet Latest Price

Product Details:

AS PER IS: 2386 The machine is used to determine the resistance of aggregate to wear by abrasion.
Salient Features

• Specification :It consists of two hollow cylinders closed at one end and provided with tight fitting covers at the either end. These cylinders are mounted on a shaft at an angle of 30 degrees with the axis of rotation of the shaft. The shaft rotates at 30-33 r.p.m. through a reduction gear operated by a motor and is provided with a revolution counter. Complete with abrassive charges consisting of 12 Nos. Hardened steel ball of 48mm dia. Suitable for operation on 440 volts, 3 phases, 50 cycles. A.C.supply.

Approx. Rs 1.25 Lakh / NumberGet Latest Price

Product Details:

These machines are electro mechanical screw driven machines with precision screw and column construction and variable speed drive. Tow option are available mainly Acme threaded screw with DC Motor drive & ball lead screw with servo drive. The machines are suitable for studying mechanical behavior of various materials like metals, polymers, elastomers etc. These machines are easy to operate and they offer excellent performance and flexibility to meet the needs of modern testing requirements. The machines confirm to IS, BS & ASTM standards. These machines are available with following options depending upon test requirements and budget, best combination can be selected. DRIVE - SD: Drive dd is with DC motor with thyrister drive to give speed ratio As per sample std. Requirement. DRIVE - SD: Drive SD is with servo motor & PWM transister drive to give speed ratio As per sample std. Requirement.

Approx. Rs 1,800 / NumberGet Latest Price

Product Details:

For density tests on aggregates as per procedure laid down.
Salient Features

• Specifications: Made of brass with stainless steel wire mesh 6.3mm size ruggedly constructed, approximately 20cm dia x 20cm high. Complete with handle.

Approx. Rs 45,000 / UnitGet Latest Price

Product Details:

We take pleasure in introducing ourselves as leading firm by offering Digital Spring Testing Machine.